MVLAN Configure in ZTE ZXA10 C220 OLT | GPON Solution

MVLAN Configure in ZTE ZXA10 C220 OLT

MVLAN Configure in ZTE ZXA10 C220 OLT

Today i will discuss how to MVLAN Configure in ZTE ZXA10 C220 OLT.

Prerequisites:

  • Make sure that the network device works normally.
  • Make sure that the multicast source exits in the uplink network.
  • Make sure that the data service is configured.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Context:

To configure the MVLAN parameters, perform the following steps:

1. Use the configure terminal command to enter global configuration mode.
2. Use the igmp mvlan command to configure MVLAN
3. Configure MVLAN groups process mode.

Use the igmp mvlan enable command to configure that the MVLAN processes multicast packets with IGMP protocol.
Use the igmp mvlan disable command to configure that the MVLAN transparently transmits multicast packets.

4. Use the igmp mvlan work-mode command to configure MVLAN work mode.

Note: In IGMP snooping mode, pre-join and static join functions are invalid.

5. Use the igmp mvlan group command to configure MVLAN group
6. Use the igmp mvlan group-filter command to configure MVLAN group management.

Note:

  • When MVLAN group management is enabled, IGMP join packets must check whether the group is configured. The configured group is management group.
  • When MVLAN group management is disabled, IGMP join packets do not check whether the group is configured. The learned group is dynamic group.
  • When span-VLAN is enabled, MVLAN group-filter must be enabled.

7. Use the igmp mvlan group bandwidth command to configure multicast bandwidth.
8. Use the igmp mvlan max-group command to configure MVLAN maximum group number.
9. Use the igmp mvlan group pre-join command to configure pre-join function.
10. Use the igmp mvlan source-port command to configure MVLAN source port.
11. Use the igmp mvlan receive-port command to configure MVLAN receiving port.
12. Use the igmp mvlan static-port command to configure MVLAN static receiving port.
13. Use the igmp mvlan host-ip command configure MVLAN proxy IP address in IGMP proxy mode.
14. Use the igmp mvlan group command to query MVLAN configuration.

MVLAN Configure Example:

Configure MVLAN 10.

  • IGMP: Enable
  • IGMP work mode: Proxy
  • Group IP address: 224.1.1.1 – 224.1.1.10
  • Group filter: Enable
  • Maximum group number: 16
  • Source port: 1/21/1
  • Receiving port: 1/5/1:1
  • Proxy host IP address: 10.63.196.50

ZXAN#configure terminal
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#igmp mvlan 10
ZXAN(config)#igmp mvlan 10 enable
ZXAN(config)#igmp mvlan 10 work-mode proxy
ZXAN(config)#igmp mvlan 10 group 224.1.1.1 to 224.1.1.10
ZXAN(config)#igmp mvlan 10 group-filter enable
ZXAN(config)#igmp mvlan 10 max-group 16
ZXAN(config)#igmp mvlan 10 source-port gei_1/21/1
ZXAN(config)#igmp mvlan 10 receive-port gpon-onu_1/5/1:1 vport 1
ZXAN(config)#igmp mvlan 10 host-ip 10.63.196.50

ZXAN(config)#show igmp mvlan 10
Protocol packet’s priority is 0 (in proxy/router mode).
Source Port
—————————-
gei_1/21/1

Receive Port
—————————-
gpon-onu_1/5/1:1:1

Group
—————————-
224.1.1.1 – 224.1.1.10

MVLAN Configure in ZTE ZXA10 C220 OLT

MVLAN Configure in ZTE ZXA10 C220 OLT

email

Shahed

Hi! I am Shahed. I currently work as a Sr. Network Engineer. I want to build up my carrier in Networking field.

Follow Me:
TwitterFacebookLinkedInPinterestGoogle PlusDiggYouTubeRedditDelicious

MVLAN Configure in ZTE ZXA10 C220 OLT was last modified: April 18th, 2016 by Shahed

Comments

comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Time limit is exhausted. Please reload CAPTCHA.

error: Content is protected !!