About Author

0x2e112004 The signal fail of ONTi (SFi) occurs

by ShahedJanuary 6, 20160

0x2e112004 The signal fail of ONTi (SFi) occurs Today i will discuss about 0x2e112004 The signal fail of ONTi (SFi) occurs alarm. System generates this alarm when a GPON port detects that the signals of an ONT fail and that the BER check error code rate in the upstream direction of the ONT reaches the threshold. [boxads] Attribute: Alarm ID Alarm Severity Alarm Type 0x2e112004 Warning Fault Impact on the System: The data link is interrupted and the data cannot be transmitted in the normal state. The services of the ONT are interrupted. Possible Causes: The optical fiber is faulty. …

by ShahedJanuary 4, 20160

0x2e112003 The signal degrade of ONTi (SDi) occurs Today i will discuss about 0x2e112003 The signal degrade of ONTi (SDi) occurs alarm. System generates this alarm when a GPON port detects that the signals of an ONT deteriorates and that the BER check error code rate in the upstream direction of the ONT reaches the threshold. [boxads] Attribute: Alarm ID Alarm Severity Alarm Type 0x2e112003 Warning Fault Impact on the System: The data transmission is unstable, and packet loss of the ONT upstream service may occur. The service quality deteriorates. Possible Causes: The quality of the optical path is poor. …

by ShahedJanuary 4, 2016January 10, 20160

Loss of GEM channel delineation (LCDGi) occurs: Today i will discuss about the loss of GEM channel delineation (LCDGi) occurs alarm. System generates this alarm when delimitation of the GEM frame header is incorrect. The OLT detects HEC check errors of the GEM header in consecutive frames and the ONT goes offline. [boxads] Attribute Alarm ID Alarm Severity Alarm Type 0x2e112002 Warning Fault Impact on the System: The loss of frame (LOF) occurs in the system, and the ONT goes offline. Possible Causes: The optical fiber is faulty. The ONT is faulty. Procedure: Check the optical fiber. If the optical fiber …

by ShahedJanuary 3, 2016January 10, 20160

Optical module fault Alarm Huawei OLT: Today I will discuss Last down cause: Optical module fault alarm. When you connect a non brand SFP or SFP not match with your OLT version then OLT display Optical module fault Alarm. I face a problem, when i connect a new SFP in H805GPFD board then 0-7 port SFP is working but 8-15 port was not working. When we connect NeoPhotonics Class B+ SFP then it work fine. bellow are the both status. [boxads] Unsupported SFP Status: NMC_Huawei_OLT02(config-if-gpon-0/0)#display port state 8 —————————————————————————- F/S/P 0/0/8 Optical Module status Online Port state Offline xPON MAC …

by ShahedDecember 24, 2015January 24, 20160

Basic Layout of Huawei OLT Today i will discuss about Basic Layout of Huawei OLT. Bellow are the details…. [boxads] Basic Layout: Chassis: bundled sales, not sold separately. MPU: generally double master, one for main and one for standby, SCUN, MCUD (MA5608T) are common used. Power Plate: generally dual power, one for main and one for standby, PRTE (DC), MPWC (DC), MPWD (AC) are common used. Upstream board: GICF, GICG, X2CS etc. GPON service boards: GPBD, GPFD etc. Software: generally has been installed inside the control board SCUN Control board – SCUN (SCUL, SCUK, SCUH) Function: Systematic control, switching and …

by ShahedDecember 21, 2015January 10, 20161

Dying gasp Alarm GPON ONTi (DGi) When ONT goes offline then Huawei OLT receives a message from ONT then system generates dying gasp alarm. If power cord remove from ONT without power off ONT device or Load shedding causes electricity power go away then system generates dying gasp alarm. [boxads] Attribute: Alarm ID Alarm Severity Alarm Type 0x2e11a00b Minor Fault Parameters: Name Meaning FrameID The ID of the shelf where the alarm is generated. SlotID The ID of the slot where the alarm is generated. PortID The ID of the port where the alarm is generated. ONT ID The ID …