September 16, 2025

Match state mismatch in Huawei ONT

Match state mismatch in Huawei ONT: When you found Match State : mismatch in Huawei ONT by display ont info command, then which type step taken you ? [boxads] Don’t  worry i will show how to solved this problem………………. This types of problem occur if ONT port & pots should not configure properly in ont srvprofile. Suppose your ONT have 2 pots & 4 eth port, If you configure 4 pots & 4 eth port or 4 pots & 2 eth port, It is not match your ONT because your ONT have 2 pots & 4 eth port. So if …

Match state mismatch in Huawei ONT Read More

H.248-based VoIP service Configure Huawei OLT

H.248-based VoIP service Configure Huawei OLT: Service Requirements: In an office located in China, the  MA5600T/MA5603T/MA5608Tthat adopts the H.248 protocol is newly deployed. Data plan and configuration, however, are not performed on the MGC (softswitch) connected to the MA5600T/MA5603T/MA5608T. The MA5600T/MA5603T/MA5608T is required to provide the following VoIP services: [boxads] The common phone services are provisioned to 32 users (phones 0-31). The polarity-reversal accounting is adopted. Technology Diagram H.248-based VoIP service: Prerequisite: According to the actual network, a route from the MA5600T/MA5603T/MA5608T to the MGC must be configured to ensure that the MA5600T/MA5603T/MA5608Tand the MGC are reachable from each other. …

H.248-based VoIP service Configure Huawei OLT Read More

Configure VoIP PSTN Service (SIP) on Huawei OLT

Configure VoIP PSTN Service (SIP): Prerequisite: According to the actual network, a route from the MA5600T/MA5603T/MA5608T to the IMS must be configured to ensure that the MA5600T/MA5603T/MA5608T and the IMS are reachable from each other. Electronic switch 0 must be in  location-1 (indicating that the system goes upstream through only the upstream board). Electronic switch 1 must be in location-0(indicating that the VoIP service is supported). For details about how to configure the electronic switch, see electro-switch. [boxads] NOTE: The SCUN and SCUH control boards do not support electronic switch. The control board SCUL does not provide the upstream port …

Configure VoIP PSTN Service (SIP) on Huawei OLT Read More

GPON Triple Play Configuration VoIP, IPTV

GPON Triple Play Configuration: [boxads] Today i will describe how to configure the Gpon Triple Play on the MA5600T/MA5603T/MA5608T. Gpon triple play is a service provisioning mode in which all integrated services can be provided to a user. Currently, the prevailing integrated services include the high-speed Internet access service, voice over IP (VoIP) service, and IPTV service. The early broadband access provides only the high-speed Internet access service. As the Internet is rapidly developing, it can offer much richer services, such as video (IPTV) services. Service Priorities and Bandwidth: The different services have different request on the bandwidth and priority. …

GPON Triple Play Configuration VoIP, IPTV Read More

SIP Interface Configure in Huawei OLT

SIP Interface Configure in Huawei OLT: As an interface used for the intercommunication between the MA5600T/MA5603T/MA5608T and the MGC, the interface is vital to the SIP-based VoIP service. Therefore, to implement the VoIP service, the SIP interface must be configured and must be in the normal state. [boxads] Procedure: Configuring the Upstream VLAN Interface: This topic describes how to specify the upstream VLAN interface for the media stream and the signaling flow, and how to configure the IP addresses of the Layer 3 interface. These IP addresses are the sources of the media and signaling IP address pools. Context: Multiple …

SIP Interface Configure in Huawei OLT Read More

Configure SIP-based FoIP Service Huawei OLT

Configure SIP-based FoIP Service in Huawei OLT: This topic describes how to configure the SIP-based FoIP service. Prerequisites: The SIP-based VoIP service must be configured. For details, see  Configuring the VoIP Service (SIP-based). The voice service port used for the FoIP service must be in the normal state, and the voice communication on the port must be normal. [boxads] Context: According to the fax coding mode, the FoIP service is classified into two modes: Transparent transmission fax: uses the G.711 coding. T.38 fax: uses the T.38 coding In the fax service application, according to whether the SIP signaling is involved …

Configure SIP-based FoIP Service Huawei OLT Read More
error: Content is protected !!