About Author

Lscable Alarm list LST20016 OLT

by ShahedApril 27, 2012October 24, 20150

Lscable Alarm list LST20016 OLT: [boxads]Bellow are the list of Lscable ONT alarm in OLT………… 1 CPU_LOAD -cpu load: when cpu Load is higher than threshold value(default: 70 Unit:%). 2 MEM_LOAD -memory load: when memory Load is higher than threshold value(default: 80 Unit: %). 3 TEMP_HIGH -temperature high: when temperature is higher than “High temperature threshold”(default : 100). 4 TEMP_LOW -temperature low: when temperature is lower than “Low temperature threshold”(default :-20). 5 DHCP_THRESHOLD -dhcp threshold The number of IPs of DHCP pool is over threshold. 6 DHCP_SHORTAGE -dhcp shortage there is no room for IP alignment. 7 UNIT_OUT -unit out …

by ShahedApril 26, 2012October 24, 20150

Huawei Gpon ONT Alarm Profile: Today i will describes how to add an alarm profile, and configure most of the performance parameters for various ONT lines as a profile. After the alarm profile is configured and bound successfully, the ONT can directly use the profile when it is activated. [boxads] An ONT alarm profile defines a series of alarm thresholds that are used to monitor the performance of an activated ONT line. When the statistics result of a parameter reaches the alarm threshold, the NE is notified and an alarm is sent to the log server and the NMS. The …

by ShahedApril 26, 2012October 24, 20150

Huawei ONT alarm policy profile create: Today i will discuss how to create Huawei ONT alarm policy profile in Huawei OLT. So lets go………. [boxads] In FTTH scenarios, you can configure the ONT alarm policy profile to configure alarms for different service policies. Step-1: Create an ONT alarm policy profile. Run the ont-alarm-policy command to create an ONT alarm policy profile. The system supports a maximum number of 16 alarm policy profiles. The default alarm policy profile is profile 0. It is recommended that you configure different alarm policies for VIP and common users. Step-2: Configure attributes of the Huawei ONT …

by ShahedApril 19, 2012October 26, 20152

Config state failed in Huawei ONT: Today i will discuss how to solved Config state failed problem in Huawei ONT. When you found Config state : failed status in Huawei ONT by display ont info, then which type step taken you ? Don’t worry i will show how to solved this problem………………. [boxads] config state failed This types of problem occur if line-profile should not configured properly, such as same GEM index is apply same PON port in different line-profile. Now show bellow step to solved that problem. step-1: At first show all service port in that pon port & …

by ShahedApril 18, 2012October 26, 20150

Match state mismatch in Huawei ONT: When you found Match State : mismatch in Huawei ONT by display ont info command, then which type step taken you ? [boxads] Don’t worry i will show how to solved this problem………………. This types of problem occur if ONT port & pots should not configure properly in ont srvprofile. Suppose your ONT have 2 pots & 4 eth port, If you configure 4 pots & 4 eth port or 4 pots & 2 eth port, It is not match your ONT because your ONT have 2 pots & 4 eth port. So if …

by ShahedApril 14, 2012October 24, 20151

H.248-based VoIP service Configure Huawei OLT: Service Requirements: In an office located in China, the MA5600T/MA5603T/MA5608Tthat adopts the H.248 protocol is newly deployed. Data plan and configuration, however, are not performed on the MGC (softswitch) connected to the MA5600T/MA5603T/MA5608T. The MA5600T/MA5603T/MA5608T is required to provide the following VoIP services: [boxads] The common phone services are provisioned to 32 users (phones 0-31). The polarity-reversal accounting is adopted. Technology Diagram H.248-based VoIP service: Prerequisite: According to the actual network, a route from the MA5600T/MA5603T/MA5608T to the MGC must be configured to ensure that the MA5600T/MA5603T/MA5608Tand the MGC are reachable from each other. …