Configure IGMP Global Parameters in ZTE OLT | GPON Solution

Configure IGMP Global Parameters in ZTE OLT

Configure IGMP Global Parameters in ZTE OLT

Today i will discuss how to Configure IGMP Global Parameters in ZTE OLT.

Prerequisites:

  • Make sure that the network device works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Configure IGMP Global Parameters in ZTE OLT 1Configure IGMP Global Parameters in ZTE OLT

Configure IGMP Global Parameters in ZTE OLT

To configure the IGMP global parameters, perform the following steps:

1. Use the configure terminal command to enter global configuration mode.
2. Use the igmp enable command to enable global IGMP protocol.
3. Use the igmp snooping-aging-time command to configure IGMP snooping aging time.
4. Use the igmp query-interval command to configure IGMP proxy general query interval.
5. Use the igmp query-max-resp command to configure IGMP proxy maximum query response time
6. Use the igmp last-query-interval command to configure IGMP proxy last member query interval.
7. Use the igmp last-query-count command to configure IGMP poxy last member query counts.
8. Use the igmp unsolicited-report-interval command to configure IGMP unsolicited report interval.
9. Use the igmp robustness command to configure IGMP proxy robustness.
10. Use the igmp log enable command to enable log function.
11. Use the igmp host-tracking command to enable host tracking function.
12. Use the igmp bandwidth-control command to enable bandwidth control function.

Note: When bandwidth control is enabled, if the user multicast bandwidth exceeds the present left bandwidth, the user join request is turned down.

13. Use the igmp span-vlan command to enable span VLAN function.
14. Use the igmp forward-cvlan command to enable CVLAN forward function.
15. Use the igmp non-match-group command to configure unmatched group process mode.
16. Use the igmp version-mode command to configure the IGMP packets process mode in IGMP v1/v2/v3.
17. Use the show igmp command to query IGMP global configuration.

Example of Configure and query IGMP global parameters:

  • Snooping aging time: 100 seconds
  • Bandwidth control: Enable
  • Span VLAN: Enable
  • Other parameters: Default values

ZXAN#configure terminal
Enter the configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#igmp enable
ZXAN(config)#igmp snooping-aging-time 100
ZZXAN(config)#igmp bandwidth-control enable
ZXAN(config)#igmp span-vlan enable
ZXAN(config)#igmp forward-cvlan enable
ZXAN(config)#igmp non-match-group drop

ZXR10(config)#show igmp
IGMP global parameters:
—————————————————-

IGMP is globally enable.
IGMP v1 mode is accept.
IGMP v2 mode is accept.
IGMP v3 mode is accept.
IGMP log is enable.
Snooping aging time is 100 seconds.
Span vlan is enable.
Forward cvlan is enable.
Bandwidth control is enable.
Host tracking is enable.
Robustness variable is 2.
General query interval is 125(second).
Query max response time is 100(0.1second).
Last member query interval is 10(0.1second).
Last member query count is 4.
Unsolicited report interval is 10 seconds.
Non match group is drop.

Configure IGMP Global Parameters in ZTE OLT

Configure IGMP Global Parameters in ZTE OLT

email

Shahed

Hi! I am Shahed. I currently work as a Sr. Network Engineer. I want to build up my carrier in Networking field.

Follow Me:
TwitterFacebookLinkedInPinterestGoogle PlusDiggYouTubeRedditDelicious

Configure IGMP Global Parameters in ZTE OLT was last modified: April 18th, 2016 by Shahed

Comments

comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Time limit is exhausted. Please reload CAPTCHA.

error: Content is protected !!