October 11, 2024

Huawei Gpon ONT Alarm Profile Configure

Huawei Gpon ONT Alarm Profile:

Today i will describes how to add an alarm profile, and configure most of the performance parameters for various ONT lines as a profile. After the alarm profile is configured and bound successfully, the ONT can directly use the profile when it is activated. [boxads]

An ONT alarm profile defines a series of alarm thresholds that are used to monitor the performance of an activated ONT line. When the statistics result of a parameter reaches the alarm threshold, the NE is notified and an alarm is sent to the log server and the NMS.

  • The MA5600T/MA5603T/MA5608T supports up to 50 alarm profiles.
  • The system contains a default alarm profile with the ID 1. This profile cannot be deleted but can be modified.

Procedure:

  • Step-1: Run the gpon alarm-profile add command to add a GPON ONT alarm profile. All parameters in the default profile are set to 0, which indicates that no alarm is reported. When an alarm profile is created, the default values of all alarm thresholds are 0, which indicates that no alarm is reported.
  • Step-2: Run the display gpon alarm-profile command to query the alarm profile.

ONT Alarm Profile Configuration Example:

[adsense] To add Huawei GPON ONT alarm profile 5, set the alarm threshold for the packet loss of the GEM port to 10, set the alarm threshold for the number of mis-transmitted packets to 30, and use the default value 0 for all other thresholds, do as follows:

huawei-OLT(config)#gpon alarm-profile add profile-id 5
{ <cr>|profile-name<K> }:
Command:
gpon alarm-profile add profile-id 5
Press ‘Q’ or ‘q’ to quit input
> GEM port loss of packets threshold (0~100)[0]:  10
> GEM port misinserted packets threshold (0~100)[0]:  30
> GEM port impaired blocks threshold (0~100)[0]:
> Ethernet FCS errors threshold (0~100)[0]:
> Ethernet excessive collision count threshold (0~100)[0]:
> Ethernet late collision count threshold (0~100)[0]:
> Too long Ethernet frames threshold (0~100)[0]:
> Ethernet buffer (Rx) overflows threshold (0~100)[0]:
> Ethernet buffer (Tx) overflows threshold (0~100)[0]:
> Ethernet single collision frame count threshold (0~100)[0]:
> Ethernet multiple collisions frame count threshold (0~100)[0]:
> Ethernet SQE count threshold (0~100)[0]:
> Ethernet deferred transmission count threshold (0~100)[0]:
> Ethernet internal MAC Tx errors threshold (0~100)[0]:
> Ethernet carrier sense errors threshold (0~100)[0]:
> Ethernet alignment errors threshold (0~100)[0]:
> Ethernet internal MAC Rx errors threshold (0~100)[0]:
> PPPOE filtered frames threshold (0~100)[0]:
> MAC bridge port discarded frames due to delay threshold (0~100)[0]:
> MAC bridge port MTU exceeded discard frames threshold (0~100)[0]:
> MAC bridge port received incorrect frames threshold (0~100)[0]:
> CES general error time threshold(0~100)[0]:
> CES severely time threshold(0~100)[0]:
> CES bursty time threshold(0~100)[0]:
> CES controlled slip threshold(0~100)[0]:
> CES unavailable time threshold(0~100)[0]:
> Drop events threshold(0~100)[0]:
> Undersize packets threshold(0~100)[0]:
> Fragments threshold(0~100)[0]:
> Jabbers threshold(0~100)[0]:
> Failed signal of ONT threshold(Format:1e-x, x: 3~8)[3]:
> Degraded signal of ONT threshold(Format:1e-x, x: 4~9)[4]:
> FEC uncorrectable code words threshold(0~1101600000)[0]:
> FEC correctable code words threshold(0~1101600000)[0]:
> Upstream PQ discarded byte alarm threshold(0~65535)[0]:6
> Downstream PQ discarded byte alarm threshold(0~65535)[0]:6
> XGEM key errors threshold(0~100)[0]:
> XGEM HEC error count threshold(0~100)[0]:
Adding an alarm profile succeeded
Profile ID : 5
Profile name: alarm-profile_5

huawei gpon ont alarm profile configure
huawei gpon ont alarm profile configure

Now we check it by bellow command…………

[bodyads]

huawei-OLT(config)#display gpon alarm-profile profile-id 5
————————————————————–
Profile ID : 5
Profile name: alarm-profile_5
————————————————————–
GEM port loss of packets threshold: 10
GEM port misinserted packets threshold: 30
GEM port impaired blocks threshold: 0
Ethernet FCS errors threshold: 0
Ethernet excessive collision count threshold: 0
Ethernet late collision count threshold: 0
Too long Ethernet frames threshold: 0
Ethernet buffer (Rx) overflows threshold: 0
Ethernet buffer (Tx) overflows threshold: 0
Ethernet single collision frame count threshold: 0
Ethernet multiple collisions frame count threshold: 0
Ethernet SQE count threshold: 0
Ethernet deferred transmission count threshold: 0
Ethernet internal MAC Tx errors threshold: 0
Ethernet carrier sense errors threshold: 0
Ethernet alignment errors threshold: 0
Ethernet internal MAC Rx errors threshold: 0
PPPOE filtered frames threshold: 0
MAC bridge port discarded frames due to delay threshold: 0
MAC bridge port MTU exceeded discard frames threshold: 0
MAC bridge port received incorrect frames threshold: 0
CES general error time threshold: 0
CES severely time threshold: 0
CES bursty time threshold: 0
CES controlled slip time threshold: 0
CES unavailable time threshold: 0
Drop events threshold: 0
Undersize packets threshold: 0
Fragments threshold: 0
Jabbers threshold: 0
Failed signal of ONU threshold (Format:1e-x): 3
Degraded signal of ONU threshold (Format:1e-x): 4
FEC uncorrectable code words threshold: 0
FEC correctable code words threshold: 0
Upstream PQ discarded byte alarm threshold: 6
Downstream PQ discarded byte alarm threshold: 6
XGEM key errors threshold: 0
XGEM HEC error count threshold: 0
————————————————————–
Binding Times: 0
————————————————————–

ONT alarm Profile
ONT alarm Profile

Now Bind this alarm profile to an ONT by bellow command:

huawei-OLT(config-if-gpon-0/4)#ont alarm-profile 1 2 profile-id 5

Shahed

Hi! I am Shahed Israr. I try to help GPON Technology users with their queries and provide them with relevant and accurate information to the best of my ability. My main goal is to assist and enhance GPON Technology user and help people find the answers they're looking for quickly and easily.

Follow Me:
TwitterFacebookLinkedInPinterestGoogle PlusDiggYouTubeRedditDelicious

Visited 456 times, 1 visit(s) today

Comments

comments

Shahed

Hi! I am Shahed Israr. I try to help GPON Technology users with their queries and provide them with relevant and accurate information to the best of my ability. My main goal is to assist and enhance GPON Technology user and help people find the answers they're looking for quickly and easily.

View all posts by Shahed →

Leave a Reply

Your email address will not be published. Required fields are marked *

Time limit is exhausted. Please reload CAPTCHA.

error: Content is protected !!