ZTE GPON

Configure IGMP Port Parameters in ZTE OLT

by

Configure IGMP Port Parameters in ZTE OLT

[boxads]

Today i will discuss how to Configure IGMP Port Parameters in ZTE OLT.

Prerequisites:

  • Make sure that the network device works normally.
  • ONU is registered.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Context:

Table 14 describes ranges and default values of IGMP port parameters.

Configure IGMP Port Parameters in ZTE OLT
Configure IGMP Port Parameters in ZTE OLT

To configure the IGMP port parameters, perform the following steps:

1. Use the configure terminal command to enter global configuration mode.
2. Use the interface command to enter GPON-ONU interface configuration mode.
3. Use the igmp enable command to enable interface IGMP protocol.
4. Use the igmp fast-leave command to configure IGMP fastleave function.
5. Use the igmp query-interval command to configure IGMP proxy general query interval.

Read more

Configure IGMP Global Parameters in ZTE OLT

by

Configure IGMP Global Parameters in ZTE OLT

[boxads]

Today i will discuss how to Configure IGMP Global Parameters in ZTE OLT.

Prerequisites:

  • Make sure that the network device works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Configure IGMP Global Parameters in ZTE OLT 1Configure IGMP Global Parameters in ZTE OLT

Configure IGMP Global Parameters in ZTE OLT

To configure the IGMP global parameters, perform the following steps:

1. Use the configure terminal command to enter global configuration mode.
2. Use the igmp enable command to enable global IGMP protocol.
3. Use the igmp snooping-aging-time command to configure IGMP snooping aging time.
4. Use the igmp query-interval command to configure IGMP proxy general query interval.
5. Use the igmp query-max-resp command to configure IGMP proxy maximum query response time
6. Use the igmp last-query-interval command to configure IGMP proxy last member query interval.
7. Use the igmp last-query-count command to configure IGMP poxy last member query counts.
8. Use the igmp unsolicited-report-interval command to configure IGMP unsolicited report interval.
9. Use the igmp robustness command to configure IGMP proxy robustness.
10. Use the igmp log enable command to enable log function.
11. Use the igmp host-tracking command to enable host tracking function.
12. Use the igmp bandwidth-control command to enable bandwidth control function.

Read more

ZTE F820 IGMP Snooping Multicast Service

by

ZTE F820 IGMP Snooping Multicast Service Configure

[boxads]

Today i will discuss how to configure ZTE F820 IGMP Snooping Multicast Service in ZTE OLT.

Prerequisites:

  • Make sure that network device works normally.
  • Make sure that multicast source exits in the uplink network.
  • Make sure that GPON card works normally.
  • Make sure that the in-band NM IP address of the ZXA10 C220 is configured.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Background Information:

When an ONU is registered on the ZXA10 C220, the OLT creates a multicast service connection automatically.

  • Bridge_0/1
  • GEM port ID: 1021
  • Uplink_0/1/255

On the ONU, the multicast service connection transmits only multicast service packets and the multicast protocol packets are transmitted in the unicast service connection.

The F820 supports 12 MVLANs and 255 multicast groups.

Networking Diagram:  ZTE F820 IGMP snooping multicast service networking diagram.

ZTE F820 IGMP snooping multicast service networking diagram.
ZTE F820 IGMP snooping multicast service networking diagram.

Configuration Data: ZTE F820 IGMP snooping multicast service configuration data

ZTE F820 IGMP snooping multicast service configuration data 1

Read more

IGMP Proxy Multicast Service Configure ZTE OLT

by

IGMP Proxy Multicast Service Configure ZTE OLT

[boxads]

Today i will discuss how IGMP Proxy Multicast Service Configure in ZTE OLT.

Prerequisites:

  • Make sure that the network device works normally.
  • Make sure that multicast source exits in the uplink network.
  • Make sure that the GPON card works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Background Information:

When an ONU is registered on the ZXA10 C220, the OLT creates a multicast service connection automatically.

  • Bridge_0/1
  • GEM port ID: 1021
  • Uplink_0/1/255

On the ONU, the multicast service connection transmits only multicast service packets and the multicast protocol packets are transmitted in the unicast service connection. The F621 supports one MVLAN and 32 multicast groups.

IGMP Proxy Multicast Service Networking Diagram:

IGMP proxy multicast service networking diagram
IGMP proxy multicast service networking diagram

Read more

IGMP Snooping Multicast Service Configure ZTE OLT

by

IGMP Snooping Multicast Service Configure ZTE OLT

[boxads]

Today i will discuss how to IGMP Snooping Multicast Service Configure in ZTE OLT.

Prerequisites:

  • Make sure that network device works normally.
  • Make sure that multicast source exits in the uplink network.
  • Make sure that GPON card works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Background Information:

When an ONU is registered on the ZXA10 C220, the OLT creates a multicast service connection automatically.

  • Bridge_0/1
  • GEM port ID: 1021
  • Uplink_0/1/255

On the ONU, the multicast service connection transmits only multicast service packets and the multicast protocol packets are transmitted in the unicast service connection.

The F621 supports one MVLAN and 32 multicast groups.

IGMP snooping multicast service networking diagram:

IGMP snooping multicast service networking
IGMP snooping multicast service networking

Read more

ZTE GPON Protection Service Configuration

by

ZTE GPON Protection Service Configuration

[boxads]

Today i will discuss how to configure ZTE GPON Protection Service. ZTE ZXA10 C220 provides GPON port protection by main and backup GPON ports switching mechanism. When the main GPON link is break, the backup takes over the GPON service automatically.

ZXA10 C220 supports three types GPON port switch mechanisms:

  • Force switch (high priority)
  • Alarm-triggered switch (middle priority)
  • Manual switch (low priority)

Configuring GPON Protection Service:

Prerequisites:

  • Make sure that network device works normally.
  • Make sure that VLAN is configured properly on uplink equipment.
  • Make sure that GPON data service is configured successfully.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

ZTE GPON protection service networking diagram:

ZTE GPON protection service networking diagram
GPON protection service networking diagram

Read more