Huawei Config

Huawei OLT/ONT Configuration

Huawei ONT alarm policy profile create

by

Huawei ONT alarm policy profile create:

Today i will discuss how to create Huawei ONT alarm policy profile in Huawei OLT. So lets go………. [boxads]

In FTTH scenarios, you can configure the ONT alarm policy profile to configure alarms for different service policies.

Step-1: Create an ONT alarm policy profile.

Run the ont-alarm-policy command to create an ONT alarm policy profile.
The system supports a maximum number of 16 alarm policy profiles.
The default alarm policy profile is profile 0.
It is recommended that you configure different alarm policies for VIP and common users.

Step-2: Configure attributes of the Huawei ONT alarm profile.

Run the alarm filter command to configure the control function of each alarm of the profile.
Run the commit command to save the configuration.
Run the display ont-alarm-policy command to query attributes of the ONT alarm policy profile.

Step-3: Bind the Huawei ONT to the ONT alarm policy profile.

Run the ont-alarm-policy command to bind the ONT to the ONT alarm policy profile so that the PON board can control whether to send the ONT alarm information.
During ONT adding or confirmation, the system binds the ONT to the default ONT alarm policy profile 0.

Read more

Config state failed in Huawei ONT

by

Config state failed in Huawei ONT:

Today i will discuss how to solved Config state failed problem in Huawei ONT. When you found Config state : failed status in Huawei ONT by display ont info, then which type step taken you ? Don’t  worry i will show how to solved this problem………………. [boxads]config state failed

config state failed

This types of problem occur if line-profile should not configured properly, such as same GEM index is apply same PON port in different line-profile. Now show bellow step to solved that problem.

step-1: At first show all service port in that pon port & copy it.

Huawei-OLT(config)#display service-port port 0/4/2 ont 8

service-port
service port

Now delete all service port by…………..

Read more

Match state mismatch in Huawei ONT

by

Match state mismatch in Huawei ONT:

When you found Match State : mismatch in Huawei ONT by display ont info command, then which type step taken you ? [boxads]

Don’t  worry i will show how to solved this problem……………….

Match state mismatch
Match state mismatch

This types of problem occur if ONT port & pots should not configure properly in ont srvprofile. Suppose your ONT have 2 pots & 4 eth port, If you configure 4 pots & 4 eth port or 4 pots & 2 eth port, It is not match your ONT because your ONT have 2 pots & 4 eth port. So if you configure srvprofile properly with pots & eth port, Then your problem will be solved.

Now i show you how to edit ont srvprofile & change mismatch pots & eth port.

Read more

H.248-based VoIP service Configure Huawei OLT

by

H.248-based VoIP service Configure Huawei OLT:

Service Requirements:

In an office located in China, the  MA5600T/MA5603T/MA5608Tthat adopts the H.248 protocol is newly deployed. Data plan and configuration, however, are not performed on the MGC (softswitch) connected to the MA5600T/MA5603T/MA5608T. The MA5600T/MA5603T/MA5608T is required to provide the following VoIP services: [boxads]

  • The common phone services are provisioned to 32 users (phones 0-31).
  • The polarity-reversal accounting is adopted.

Technology Diagram H.248-based VoIP service:

H.248-based VoIP service Configure Huawei OLT
H.248-based VoIP service Configure Huawei OLT

Prerequisite:

  • According to the actual network, a route from the MA5600T/MA5603T/MA5608T to the MGC must be configured to ensure that the MA5600T/MA5603T/MA5608Tand the MGC are reachable from each other.
  • Electronic switch 0 must be in  location-1(indicating that the system goes upstream through only the upstream board). Electronic switch 1 must be in location-0(indicating that the VoIP service is supported). For details about how to configure the electronic switch, see electro-switch.

Procedure:

Step 1: Add the upstream VLAN interface.

According to the data plan, configure standard VLAN 20 as the media and signaling upstream VLAN, add upstream port 0/19/0 to the VLAN, and configure the IP address of the Layer 3 interface to 10.10.10.10, which facilitates the configuration of the media and signaling IP address
pools.

Huawei-OLT(config)#vlan 20 standard
Huawei-OLT(config)#port vlan 20 0/19 0
Huawei-OLT(config)#interface vlanif 20
Huawei-OLT(config-if-vlanif20)#ip address 10.10.10.10 24
Huawei-OLT(config-if-vlanif20)#quit

Read more

Configure VoIP PSTN Service (SIP) on Huawei OLT

by

Configure VoIP PSTN Service (SIP):

Prerequisite:

According to the actual network, a route from the MA5600T/MA5603T/MA5608T to the IMS must be configured to ensure that the MA5600T/MA5603T/MA5608T and the IMS are reachable from each other. Electronic switch 0 must be in  location-1 (indicating that the system goes upstream through only the upstream board). Electronic switch 1 must be in location-0(indicating that the VoIP service is supported). For details about how to configure the electronic switch, see electro-switch. [boxads]

NOTE:

  • The SCUN and SCUH control boards do not support electronic switch.
  • The control board SCUL does not provide the upstream port and the system goes upstream through only the upstream board.

Topology Diagram for Configure VoIP PSTN Service (SIP):

Configure VoIP PSTN Service (SIP) on Huawei OLT
Configure VoIP PSTN Service (SIP) on Huawei OLT

Procedure:

Step 1: Add the upstream VLAN interface:

Configure standard VLAN 20 as the media and signaling upstream VLAN, add upstream port 0/19/0 to the VLAN, and configure the IP address of the Layer 3 interface to 10.10.10.10, which facilitates the configuration of the media and signaling IP address pools.

Huawei-OLT(config)#vlan 20 standard
Huawei-OLT(config)#port vlan 20 0/19 0
Huawei-OLT(config)#interface vlanif 20
Huawei-OLT(config-if-vlanif20)#ip address 10.10.10.10 24
Huawei-OLT(config-if-vlanif20)#quit

Read more

GPON Triple Play Configuration VoIP, IPTV

by

GPON Triple Play Configuration: [boxads] Today i will describe how to configure the Gpon Triple Play on the MA5600T/MA5603T/MA5608T. Gpon triple play is a service provisioning mode in which all integrated services can be provided to a user. Currently, the prevailing integrated services include the high-speed Internet access service, voice over IP (VoIP) service, and … Read more