ZTE GPON

ZTE-F622 ONU register ZXA10 C220 OLT

by

ZTE-F622 ONU register ZXA10 C220 OLT

[boxads]

Today i will discuss about how to ZTE-F622 ONU register in ZTE ZXA10 C220 OLT. So follow bellow instruction.

Prerequisites:

  • Make sure that the network device works normally.
  • Make sure that the GPON card works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Context:

To register the ONU, perform the following steps:

Step-1: Use the show onu-type gpon command to query GPON ONU types.
Step-2: Use the show gpon onu uncfg command to query unauthenticated ONU.
Step-3: Use the configure terminal command to enter the global configuration mode.
Step-4: Use the interface command to enter the GPON-OLT interface configuration mode.
Step-5: Use the register command to register ONU.
Step-6:  Use the show gpon onu state command to query state of registered ONU.

Read more

ZTE ZXA10 MDU ONU F820 Data Service Configure

by

ZTE ZXA10 MDU ONU F820 Data Service Configure

[boxads]

Today i will discuss how to ZTE ZXA10 MDU ONU F820 Data Service Configure in ZTE OLT.

Prerequisites:

  • Make sure that the network device works normally.
  • Make sure that the VLAN is configured properly on uplink equipment.
  • Make sure that the in-band NM IP address of the ZXA10 C220 is configured.
  •  Make sure that the GPON card works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

F820 GPON SERVICE CONFIGURATION DATA:

Service VLAN:

  • VLAN ID: 100
  • Priority: 1

Uplink port: 0/14/1

GPON port: 0/5/1

Bandwidth profile:

  • Profile name: T1–50M
  • Bandwidth type: Maximum (Type4)
  • Bandwidth: 50 Mbps

ONU:

  • ONU ID: 1
  • ONU authentication mode: SN
  • ONU type: F820
  • ONU SN: ZTEG9000002B

ONU in-band NM:

  • VLAN ID: 1000
  • Priority: 1
  • IP address: 10.67.1.11
  • Subnet mask: 255.255.255.0
  • Gateway: 10.67.1.254

T-CONT:

  • T-CONT index: 1
  • T-CONT name: Tcont50M
  • Bandwidth profile: T1–50M
  • Alloc ID: Auto-allocate

GEM port 1:

  • T-CONT index: 1
  • GEM Port index: 1
  • GEM Port name: NMport
  • Port ID: Auto-allocate

GEM port 2:

  • T-CONT index: 1
  • GEM Port index: 2
  • GEM Port name: Gemport2
  • Port ID: Auto-allocate

ONU NM service connection:

  • GEM port name: NMport
  • Bridge: 0/1
  • Uplink interface: 0/1/1
  • Connection type: bridge +dot1p

ONU unicast service connection:

  • GEM port name: Gemport2
  • UNI: fei_0/1/1
  • Bridge: 0/1
  • Uplink interface: 0/1/2
  • Connection type: 802.1p +bridge

Read more

ZTE ONU Register in ZXA10 C220 OLT

by

ZTE ONU Register in ZXA10 C220 OLT

[boxads]

Today i will show how to configure / ZTE ONU Register in ZXA10 C220 OLT.

Prerequisites:

  • Make sure that the network device works normally.
  • Make sure that the VLAN is configured properly on uplink equipment.
  • Make sure that the GPON card works normally.
  • Log in to the ZXA10 C220 through Console or Telnet.

Connect a PC to an FE/GE port of an ONU. The ONU adds VLAN tag to user’s data at FE/GE port and sends user data to different service channel according to VLAN and priority. The ZXA10 C220 performs the mapping from GEM port to Ethernet frame and sends data out through the uplink port.

Configuration Data:

Service VLAN:

  • VLAN ID: 100
  • Priority: 1

Uplink port: 0/14/1

GPON port: 0/5/1

Bandwidth profile:

  • Profile name: T1–50M
  • Bandwidth type: Maximum (Type 4)
  • Bandwidth: 50 Mbps

ONU:

  • ONU ID: 1
  • ONU type: F621
  • ONU SN: ZTE_06120664

T-CONT:

  • T-CONT index: 1
  • T-CONT name: Tcont50M
  • Bandwidth profile: T1–50M
  • Alloc ID: Auto-allocate

GEM port:

  • T-CONT index: 1
  • GEM Port index: 1
  • GEM Port nameGemport1
  • Port ID: Auto-allocate

ONU unicast service connection:

  • GEM port name: Gemport1
  • UNI: eth_0/1
  • Bridge: 0/1
  • Uplink interface: 0/1/1
  • Connection type: 802.1p + bridge

Read more

Card Reset ZTE OLT & Swapping Main/Backup Card

by

Card Reset ZTE OLT & Swapping Main/Backup Card

[boxads]

Today i will discuss how to Card Reset ZTE OLT & Swapping Main/Backup Card.

Card Reset ZTE OLT:

Prerequisites:

  • Make sure network device works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Context:

A card is reset in the following scenarios.

  • The card is faulty.
  • The card version is upgraded.

To reset the card, performs the following steps:

Step-1. Use the reset-card command to reset card.

Example: Reset the card in slot 5.

ZXAN#reset-card slotno 5
Confirm to reset card? [yes/no]:y

Read more

Card Add Delete ZTE GPON OLT ZXA10 C220

by

Card Add Delete ZTE GPON OLT ZXA10 C220

[boxads]

Today i will discuss how to Card Add Delete ZTE GPON OLT ZXA10 C220.

Card Add ZTE GPON OLT

Prerequisites:

  • Make sure that network device works normally.
  • Make sure that the shelf is configured.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Context:

To configure the card, performs the following steps:

Step-1. Use the configure terminal command to enter global configuration mode.
Step-2. Use the add-card command to configure card.

Note: The ZXA10 C220 identifies control switching cards automatically. The other cards are installed in slots 1 – 6 and 9 – 14.

Step-3. Use the show card command to query card configuration.

Card Add ZTE GPON OLT ZXA10 C220 Example:

Add a GPON card (GPFA) to slot 5. Add a uplink card (EIGM) to slot 14.

ZXAN#configure terminal
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#add-card slotno 5 GPFA
ZXAN(config)#add-card slotno 14 EIGM

Read more

ZTE OLT Rack Shelf Configure

by

ZTE OLT Rack Shelf Configure

[boxads]

Today i will discuss how to add ZTE OLT Rack Shelf by CLI mode.

Rack Configure:

Prerequisites:

  • Make sure that the network device works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Context:

The ZXA10 C220 supports only one type of racks: ZXPON.

To configure the rack, performs the following steps:

Step-1. Use the configure terminal command to enter global configuration mode.
Step-2. Use the add-rack command to configure rack.

Note: The ZXA10 C220 supports only one rack at present, thus the rackno can only be 0.

Step-3. Use the show rack command to query rack configuration.

ZTE OLT Rack Configure Example:

Configure rack 0, and the rack type is ZXPON.

ZXAN#configure terminal
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#add-rack rackno 0 racktype ZXPON

Read more