Card Add Delete ZTE GPON OLT ZXA10 C220 | GPON Solution

Card Add Delete ZTE GPON OLT ZXA10 C220

Card Add Delete ZTE GPON OLT ZXA10 C220

Today i will discuss how to Card Add Delete ZTE GPON OLT ZXA10 C220.

Card Add ZTE GPON OLT

Prerequisites:

  • Make sure that network device works normally.
  • Make sure that the shelf is configured.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Context:

To configure the card, performs the following steps:

Step-1. Use the configure terminal command to enter global configuration mode.
Step-2. Use the add-card command to configure card.

Note: The ZXA10 C220 identifies control switching cards automatically. The other cards are installed in slots 1 – 6 and 9 – 14.

Step-3. Use the show card command to query card configuration.

Card Add ZTE GPON OLT ZXA10 C220 Example:

Add a GPON card (GPFA) to slot 5. Add a uplink card (EIGM) to slot 14.

ZXAN#configure terminal
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#add-card slotno 5 GPFA
ZXAN(config)#add-card slotno 14 EIGM

ZXAN(config)#show card
Rack Shelf  Slot  CfgType  RealType  Port   HardVer  SoftVer     Status
-------------------------------------------------------------------------
0    0      5     GPFA     GPFAB     4      V0       V1.1.2P1T6  INSERVICE
0    0      7     GCSD     GCSD      0      V1       V1.1.2P1T6  INSERVICE
0    0      8     GCSD               0                           OFFLINE
0    0      14    EIGM     EIGM      4      V0       V1.1.2P1T6  INSERVICE

show card

Card Delete ZTE GPON OLT

Prerequisites:

  • Make sure that network device works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Context:

When a card in a slot is replaced with a card of another type, delete the card and configure it again.
The control switching cards cannot be deleted.

To delete the card, performs the following steps:

Step-1. Use the configure terminal command to enter global configuration mode.
Step-2. Use the del-card command to delete card.
Step-3. Use the show card command to query card configuration.

Card Delete ZTE GPON OLT Example:

Delete the card in slot 5.

ZXAN#configure terminal
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#del-card slotno 5
Confirm to delete card? [yes/no]:yes

ZXAN(config)#show card
Rack Shelf  Slot  CfgType  RealType  Port   HardVer  SoftVer     Status
-------------------------------------------------------------------------
0    0      7     GCSD     GCSD      0      V1       V1.1.2P1T6  INSERVICE
0    0      8     GCSD               0                           OFFLINE
0    0      14    EIGM     EIGM      4      V0       V1.1.2P1T6  INSERVICE
Card Add Delete ZTE GPON OLT ZXA10 C220

Card Add Delete ZTE GPON OLT ZXA10 C220

email

Shahed

Hi! I am Shahed. I currently work as a Sr. Network Engineer. I want to build up my carrier in Networking field.

Follow Me:
TwitterFacebookLinkedInPinterestGoogle PlusDiggYouTubeRedditDelicious

Card Add Delete ZTE GPON OLT ZXA10 C220 was last modified: March 17th, 2016 by Shahed

Comments

comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Time limit is exhausted. Please reload CAPTCHA.

error: Content is protected !!